Switch-M24eG(PN28240K) Release Note October 7, 2021 Version 3.0.0.03 - Resolved Issues: 1. If you configure "dot1x control-direction in", receiving packets are forword to other ports even though the port is not authenticated. June 11, 2021: Version 3.0.0.02 - Specification Changes: 1.The default value of Energy Efficient Ethernet (EEE) has been changed to Disable. - Resolved Issues: 1.When setting the threshold value of a storm control on the menu, the value is set to 0 after you press "Enter" without entering a (numerical) value. 2.The timing to implement an optimization of a file system 3.On the port (before authenticating the WEB) where the WEB authentication is enabled, obtaining an IP address through DHCP results in a failure. 4.A specific IP address cannot be set to a default gateway. 5.When the connection with an SNTP server is not available, CLI does not respond after you execute the "sntp updatehcommand. -Note You update to firmware version 3.0.0.02 or later, the Energy Efficient Ethernet (EEE) settings will be Disable. If you want to operate with EEE settings Enable, update to firmware version 3.0.0.02 or later and then enable EEE settings. December 21, 2018: Version 3.0.0.00 - Add New Function: 1.PPSP(Power to Progress SDN@Protocol) - Resolved Issues: 1. Loop Detection function does not operate normally on the port which the PVID is set , after the configuration with an arbitrary PVID is applied from the TFTP server. November 7, 2018: Version 2.0.1.10 - Resolved Issues: 1.SNMP trap is not sent when loop is detected in Ver. 2.0.1.05 or later version. 2.When multiple management VLANs are enabled, multiple responses may be returned to one management packet addressed to itself. July 4, 2018: Version 2.0.1.08 - Resolved Issues: 1.CPU hangs-up issue: Exception occurred in FDB process and occurred communication fail. 2.When Authentication function was enabled and it received the packet of max authentication host in short time, authentication function does not work correctly. 3.When it receives the packet at the port which authentication function was enabled and the entry has already registered by other port in FDB, FDB and authentication table are not updated at the port which authentication function was enabled. April 3, 2018: Version 2.0.1.07 - Add New Function: 1.Display Serial number ¦It will be supported from May 2018. - Resolved Issues: 1.When execute the command "no dot1x forceAuthorized mac", all the entries were deleted in the authentication table. 2.When Authentication function was enabled and occurred Link down, CPU buffer was not release and occurred communication failer. 3.ACL does not work correctly. 4.When change the login password at Menu, if the number of characters for re-entering the password is different from the number of characters in the password input for the first time and the entered characters match, it will be changed to the password entered for the first time. 5.If it does not input "q" three times, it can not stop the display in the show tech. 6.The PVID setting does not appear in the configuration display, when PVID is set as a member of link agreement. January 10, 2018: Version 2.0.1.05 - Resolved Issues: 1.Display of Criterion is inappropriate at "show aggregation-link" command. 1. Modify "src-dst-mac" to "src-dst-mac / src-dst-ip / src-dst-L4-port" - Specification Changes: 1.Added blocking mode at Loop detection function. Changed default mode "shutdown" to "blocking". 2.Changed Total byte value of TX and RX Statistics. - Known Issues 1.The PVID setting does not appear in the configuration display, when PVID is set as a member of link agreement. October 30, 2017: Version 2.0.1.04 - Resolved Issues: 1.In the MAC authentication function, the MAC address may not be authenticated in some cases. 2.In the MAC authentication function, it is sometimes impossible to transfer a packet transmitted from a device having an authenticated MAC address. 3.The display of the VLAN member information becomes abnormal value, when setting the PVID after setting the guest VLAN and default VLAN. February 14, 2017: Version 2.0.1.01 - Add New Function: 1.IEEE802.1X MAC base authentication 2.MAC authentication 3.WEB authentication 4.Dynamic VLAN 5.Triple authentication (IEEE802.1X/MAC/WEB authentication can be awaited simultaneously on 1 port) (For details, refer to the instructions) - Resolved Issues: 1.Can not connect to server when IPv6 link local address is setted to server address of NTP and Syslog. 2.When member port of available port group and inavailable port group are duplicate, packet is transmitted from member port of available port group to member port of inavailable port group. 3.After PVID of all port is setted other than 1, become that can not communicate to SW when PVID of link up port is setted 1. 4.RADIUS server is setted more two address and change IP address, connection order of RADIUS server become uncertainty. 5.Configuration is not changed, when initialize setting of SNMP User, SNMP View and SNMP Group are removed. 6.ARP packet with VLAN tag is sent less than 64 byte from SW. 7.When top of login password is setted #, login password become null. 8.Can not register static MAC address when other than minimum port number of link-aggregation group is selected. 9.By particular operation, Link Aggregation Group ID(Menu) become to not display. 10.Become error when member port of Link Aggregation is selected by "show mac-address-table interface" command. 11.It does not accept the setting to disable IPv6 in IPv6 parameters all menu settings. 12.When the server is disabled, if other connected Telnet sessions are in CLI mode, they will automatically switch to the menu. (Even if the server is disabled, the session being connected will not be disconnected.It changes to a state not accepting new sessions. ) 13.When the Arp packet is received at the wire rate, the CPU usage rate is displayed as 100%. 14.The loop detection LED does not turn off when setting a port being loop detected as a member when creating a group of link aggregation. 15.In the CLI mode, if the interface list specified when entering the interface configuration mode is too long, it will not enter the interface mode and an error will result. 16.If the fiber port is linked up with the Auto MDI setting of the combo port set to Disable, the Auto MDI setting will be displayed as Enable. 17.When connecting the SFP port with loop detection on the UTP port In the combo port, link up even during loop detection. 18.In the SNMP trap individual setting menu (Enable / Disable Individual Trap Menu) of the menu, there is no valid / invalid setting of FAN Fail trap. 19.Changing the temperature threshold of the Trap(Temperature Threshold) transmission causes incorrect settings that do not exist to be displayed in show running-config. 20.On the port-by-port display of the access control policy sequence(Display Sequence By Port), the help indication of the input port range displays (display of input example) the port number that does not exist on the actual device. 21.Can not modify access control policy configuration, when do not modify sequence number. 22.While execute PING in Menu, it is accept invalid character. And the character are corrupted. 23.Can not display next page in Static Multicast Menu interface. 24.Can not modify IPv6 default gateway to "::" at batch setting command of IPv6 iSet IPv6 Parameter). 25.Can not modify Acceptable Frame Type configuration when connect by Telnet. 26.Does not display confirmation message to select connection server type (IPv4 or IPv6 address), when execute configration upload or download in Menu interface. 27.Some parameter check logic are inappropriate. 28.Does not display error message, when set invalid configration about some configration. 29.Can not input "0" (all port) to specific member port at Port Group Configuration Menu. 30.The button name is inappropriate at System log page of Web interface. 1. Modify "New Page" button name to "Last Page". 2. Modify "Display Syslog of Number" button name to "Go to specific log number". 31.Some string are incorrect in user interface. 32.Can not modify IP address by Web interface. March 14, 2016: Version 2.0.0.01 First release.